Special Announcement:  Abis tonearms will be sold under a new name, Sorane.  The production and design are exactly the same, being produced in the same facility.  The ownership of the design has reverted to the OEM.  Please click HERE to be redirected to the Sorane page.

The Abis SA1.2B 9.4″ Gimbal Tonearm

$2,000 MSRP for black version

News:  You can find Art Dudley’s review of the updated SA1.2 here.

Dealers:  You can hear and purchase arms from these fine dealers/builders.

I am offering special pricing on Yamamoto Sound Craft headshells to existing and future Abis owners.  The Yamamoto HS3, weighing a little over 8 grams, is a perfect headshell for the SA1.2, especially for medium compliance cartridges, like the Grados.

The SA1.2 was added to Stereophile’s Class A list of recommended tonearms in the April 2016 issue.

Stereophile Recommended Components

Abis SA1B Tonear

The SA1.2B is the black version of the SA1.2, and all other specifications are the same.  With the introduction of the SA1.2B tonearm, along with the improved SA1.2, Abis has improved the performance of the original SA1 tonearm, already recognized by Stereophile as a meritorious design.  Though current Abis SA1.2 arms are substantially the same as the first version of the SA1 tonearm, the refinements in bearings and geometry improve on the performance of the original.  The result is an arm with substantial authority, the same as the original arm, but with even greater refinement and delicacy.

[gview file=”https://mockingbirddistribution.com/wp-content/uploads/2013/12/SA1.2-Brochure.pdf” save=”1″]

Abis SA1B topKey to the performance of the SA1.2 and SA1.2B is the use of very high grade ball bearings. Bearings used for horizontal movement are axial-loaded, angular-contact, thrust-bearings. These thrust bearings have zero play and are held in contact by gravity.  You can think of them as acting like a unipivot, but with more than one contact point.  Because they have two tapered seats, they will self-align in the presence of a load (gravity), have exceedingly low moving friction and are especially suited to angular and axial loads.  

The angular error needed to misalign these special bearings, commonly used in high precision machinery, are so severe that they fall well outside the operating conditions for a turntable (if you need an arm for playing in zero gravity, or turned at 90° to earth’s gravity, you will be forced to use a different style of tonearm).  Traditional deep-grooved ball-bearings are not specifically designed to take an axial load, being better suited for radial loads like a wheel bearing, and they suffer from much higher rolling resistance.  While the quality of the bearing materials are a key to success, the proper choice and loading of bearings is just as important.

angular contact thrust bearing

Angular Contact Thrust Bearing

 

 

High Precision Radial Bearings

 

Also key to the performance of all tonearms, and especially the SA1.2 and SA1.2B, is the resonance characteristics of the arm “tube”.  The SA1 design is built from four pieces of billet aluminum, milled to tight tolerances, finished, fitted by hand, and torqued to settings determined by experimental observations.  The torque values chosen introduces preload on the fasteners, and produces hysteresis stresses (basically, inner friction) in the crystalline structure of the metal.  These stresses damp vibration by forcing the crystalline structure to be more tightly bound, than when in a free state.  The elastic and anelastic properties of all four pieces are slightly different, preventing dominant acoustical nodes from developing.

When properly machined, fitted and torqued, a unit composed of several milled pieces will have lower maximum resonance, with several smaller resonance frequencies, compared to an armtube composed of one piece.  These statements are backed up by scientific study into weapons systems, rockets, engines, structural elements, etc..  Resonance is a key source of failure, and the research proves the point:  a single piece of billet material can have 1~3 dominant resonance frequencies, with one resonance frequency dominating the performance of the structural member. If you think about the bars that form the notes on a xylophone, you will have a practical understanding of the limitations of “one-piece” arm tubes.  In practice, a combination of surface finish, damping materials, shape, density, alloy, crystalline structure, fastening technique, and fastener preload, among others, will determine the relative distribution of acoustic energy in a tonearm.  Since extremely dense (heavy) materials, like depleted Uranium, don’t easily lend themselves for use in tonearms, a holistic approach is necessary.

For a more thorough, and scientifically correct overview, you should start with this paper from Los Alamos

The rectangular shape, the tight assembly by hand, and the nature of billet aluminum creates a low-resonance design that is essentially quiet.  The preference for 12″ arms has more to do with compliance match, than the theoretical advantages of a 12″ arm (which are nullified by the use of a spherical tip).  The SA1.2 and SA1.2B maximize the possible geometry at 9.4″, while excellent damping and high mass give it the tonal balance of 12″ arms.  With the SA1.2 and SA1.2B, the tracking error is very low, while the superior sonic signature of the billet aluminum arm parts, and the mass equivalent to most 12″ arms, gives 12″ arm sound in a compact form.  It is ideally suited for low to medium compliance cartridges, especially those that are particularly problematic when it comes to mistracking.  

Abis SA1-2 Geometry

One thing not always stated in tonearm literature is whether the tonearm in question uses the Stevenson, Baerwald or Lofgren geometries.  In many cases, older arms adhered to the Stevenson standard.  The theory behind the Stevenson alignment is that it lowers distortion on the inner grooves, which are often the most challenging when playing symphonies/operas/soundtracks etc..  Since then, there was a sea change.  Pop and rock outsell classical several hundred to one.  In light of current trends, the Baerwald geometry works better for many pop disks, which tend to have high levels of modulation in varying areas (at the discretion of the producer and group, the loudest track could be anywhere on a disk).  

Since there is no correct answer to this question of geometry, the Abis SA1-2 geometry was chosen to fall at a point between Stevenson and Baerwald (Lofgren A).  You can adjust the overhang to make the arm perform more like the Baerwald (Lofgren A) or Stevenson geometries, if you desire (see below).  Here are the results using the supplied protractor, assuming the spindle-to-pivot distance is correct:

SA1.2 tracking comparison

 

Here are the actual projected distortion levels:

sa1.2 distortion figures

This shows that the SA1.2 is comparable to the standard curves.  It does, however, require the Arc Protractor to get the lowest possible distortion from the arm, and actually line up to the custom geometry chosen by Abis.

One other thing should be noted.  By slightly changing the overhang of the cartridge, the geometry can be made more like Stevenson or Baerwald (Lofgren A).  I experimented with minor changes in overhang and came up with some interesting results.  

[gview file=”https://mockingbirddistribution.com/wp-content/uploads/2015/09/SA1.2-Overhang.pdf”]

An important thing to remember is that unless your arm exactly matches the geometry of a given generic protractor, the generic protractor might cause noticeably higher distortion.  Generic protractors can use any popular alignment, or even use a custom alignment.  You should know if your arm is compatible.  If you go to Vinyl Engine and input your tonearm’s specifications, and they do not exactly match Stevenson or Baerwald, and you don’t have a factory supplied protractor, you should have a custom arc protractor made.  This is why I supply the Accutrak Protractor with Abis tonearms.

As a value added feature, and to accurately adjust your new tonearm, all Abis arms will come with an Accutrak arc protractor.  Click below to see the details.

All Abis Tonearms Now Include an Accutrak Protractor

All Abis Tonearms Now Include an Accutrak Protractor

 

[gview file=”https://mockingbirddistribution.com/wp-content/uploads/2015/09/Abis-Accutrak.pdf”]

 

 

 

Abis SA1 and SA1B tonearms

 

Whole Length310mm
Effective Length (Tonearm pivot – stylus)239mm (9.4″)
Practical Length (Tonearm pivot – Spindle)223mm
Overhang16mm
Offset angle22.25°
Horizontal moving sensitivity30mg
Vertical moving sensitivity20mg
Vertical Tracking Force (VTF) range0-4.5g (2.5g + 2.0g)
Cartridge + Headshell weight range15-45g
Height Adjustment(Plinth to arm wand centerline)15-55mm
Vertical BearingMiniature Radial Bearing
Horizontal BearingMiniature Radial Bearing
Output plugRCA (XLR : Option)
Output cableSingle core shield copper
Tonearm Audio Lead wireOFC 4N Copper (Separate wiring in wand)
Headshell lead wireCopper with gold plated terminal
HeadshellMachine tooled Aluminum
Tonearm Net Weight750g
Attached standard Headshell Net Weight17g

 

 

 

Jasmine SME2R10 Tonearm Base Converter

Jasmine SME2R10

The SME2R10, created by Jasmine, is a very high quality adapter that will allow Abis tonearms to be adapted to armboards drilled for the SME tonearms. They are made of quality billet aluminum and both finish and machining are excellent.

Jasmine SME2R10 bottom

Though the situation is somewhat dependent on the competency of whoever drilled the original armboard holes, the range of adjustment of the SME2R10 will allow an Abis SA1.2 to be used in place of a 3009 or 3010.

Jasmine SME2R10 side

To compare the practical distance, or spindle to pivot, here are a list of arms of similar length.

Jasmine SME2R10 set screw

Abis TA1

216 mm

Abis SA1.2

223 mm

SME 3009 R

215.4 mm

SME 3009 series II improved

215.7 mm

SME 3010 R

222 mm

SME 309

215.35 mm

SME 310

222 mm

SME M2 10”

222 mm

SME M2 9”

215.4 mm

SME Series III

215.4 mm

SME Series IV

215.35 mm

SME Series V

215.35 mm

It can be seen immediately that the TA1 is very close to the 3009, and the SA1.2 is very close to the 310 and 3010. What is not as apparent is whether or not the SA1.2 will fit in place of a 3009. If the center of the SME base for an 3009 is drilled at 215 mm, then the SA1.2 will definitely work. There is a difference of only 7.3 mm (0.287” or 19/64”). The range of adjustment for the Abis SME2R10 is much greater. It will work.

What is a slightly tougher fit will be going from SME 3012 to Abis TA1L, with a difference of 14.6 mm, or 0.574”. It is possible that some boards will allow enough room. Again, it depends on the choices made when the armboard was drilled for the 3012.

Obviously, if the SME base is mounted on an adjustable armboard or “pod”, there shouldn’t be a problem with geometry, and the Jasmine SME2R10 will allow any Abis arm to be quickly substituted for the original SME arm.

The cost of the Jasmine adapter is $60 with the purchase of an Abis tonearm.  

 

 

 [gview file=”https://mockingbirddistribution.com/wp-content/uploads/2013/12/SA-1Manual.pdf” save=”1″]

 

Sibatech of Tokyo Japan

Custom made in Japan for SIBATECH, Inc., Tokyo, Japan

 

 

    Your Name (required)

    Your Email (required)

    Subject

    Your Message

     

    rel=”publisher”>Find us on Google+

     

    rel=”author”>Find us on Google+

     

    [googleplusauthor]